¿Podemos suponer que tienes buena cobertura y que has configurado correctamente el usuario y contraseña (que te suministra el proveedor) con pppconfig?

saludos!

Hola amigo, en estos momentos es que pude contestarte, fijate que con respecto a la cobertura hay buena cobertura, ahora bien, con respecto a la configuracion lo hice hasta donde logicamente creo que lo estoy haciendo bien, con todos los parametros del proveedor, pero lo que si me llamo la atencion es que en el pppconfig la parte los puertos del modem me trae: ttys1, ttys2, ttys3, ttys0 y por defecto me recomienda el ttys1, tambien me llama la atencion es que no me muestra el puerto del modem como ttyUSB0??

Gracias y agradezco toda la orientacion posible, sera que me falta ejecutar algun comando??.

Saludos.

¿puedes conectar la tarjeta una vez esté encendido el pc y postear el resultado del comando dmesg?

saludos,

Buenas tardes, anexo informacion al ejecutar el comando dmesg:

[ 0.974150] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.974150] assign_interrupt_mode Found MSI capability
[ 0.974150] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.974150] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.974150] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.974150] assign_interrupt_mode Found MSI capability
[ 0.974150] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.974150] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.974150] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.974150] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.974150] assign_interrupt_mode Found MSI capability
[ 0.974150] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.974150] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.974150] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.974150] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.974150] assign_interrupt_mode Found MSI capability
[ 0.974150] Allocate Port Service[0000:00:1c.3:pcie00]
[ 0.974150] Allocate Port Service[0000:00:1c.3:pcie02]
[ 0.974150] Allocate Port Service[0000:00:1c.3:pcie03]
[ 0.974150] isapnp: Scanning for PnP cards...
[ 1.329989] isapnp: No Plug & Play device found
[ 1.332184] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.332184] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.332184] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.332190] brd: module loaded
[ 1.332190] PNP: PS/2 Controller [PNP0303:C20E,PNP0f13:C20F] at 0x60,0x64 irq 1,12
[ 1.339922] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.340196] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.340196] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.340196] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.340196] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.340400] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.340400] mice: PS/2 mouse device common for all mice
[ 1.340400] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 1.340400] rtc0: alarms up to one month, y3k
[ 1.340400] cpuidle: using governor ladder
[ 1.340404] cpuidle: using governor menu
[ 1.340521] No iBFT detected.
[ 1.341065] TCP cubic registered
[ 1.341178] NET: Registered protocol family 17
[ 1.341296] Using IPI No-Shortcut mode
[ 1.344269] registered taskstats version 1
[ 1.344269] rtc_cmos 00:08: setting system clock to 2009-06-01 13:32:42 UTC (1243863162)
[ 1.344269] Freeing unused kernel memory: 244k freed
[ 1.372173] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.443617] ACPI: Transitioning device [C318] to D3
[ 1.443617] ACPI: PNP0C0B:00 is registered as cooling_device0
[ 1.443742] ACPI: Fan [C318] (off)
[ 1.444065] ACPI: Transitioning device [C319] to D3
[ 1.444219] ACPI: PNP0C0B:01 is registered as cooling_device1
[ 1.444338] ACPI: Fan [C319] (off)
[ 1.444660] ACPI: Transitioning device [C31A] to D3
[ 1.444815] ACPI: PNP0C0B:02 is registered as cooling_device2
[ 1.444934] ACPI: Fan [C31A] (off)
[ 1.445255] ACPI: Transitioning device [C31B] to D3
[ 1.445408] ACPI: PNP0C0B:03 is registered as cooling_device3
[ 1.445527] ACPI: Fan [C31B] (off)
[ 1.445849] ACPI: Transitioning device [C31C] to D3
[ 1.446001] ACPI: PNP0C0B:04 is registered as cooling_device4
[ 1.446120] ACPI: Fan [C31C] (off)
[ 1.446441] ACPI: Transitioning device [C31D] to D3
[ 1.446595] ACPI: PNP0C0B:05 is registered as cooling_device5
[ 1.448906] ACPI: Fan [C31D] (off)
[ 1.449112] ACPI: Transitioning device [C31E] to D3
[ 1.449923] ACPI: PNP0C0B:06 is registered as cooling_device6
[ 1.449923] ACPI: Fan [C31E] (off)
[ 1.454408] ACPI: ACPI0007:00 is registered as cooling_device7
[ 1.454408] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.457809] ACPI: ACPI0007:01 is registered as cooling_device8
[ 1.457809] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.498742] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.502741] ACPI: Thermal Zone [TZ0] (72 C)
[ 1.524563] ACPI: LNXTHERM:02 is registered as thermal_zone1
[ 1.531694] ACPI: Thermal Zone [TZ1] (72 C)
[ 1.548828] ACPI: LNXTHERM:03 is registered as thermal_zone2
[ 1.557448] ACPI: Thermal Zone [TZ2] (63 C)
[ 1.561441] ACPI: LNXTHERM:04 is registered as thermal_zone3
[ 1.565789] ACPI: Thermal Zone [TZ3] (33 C)
[ 1.565789] ACPI: LNXTHERM:05 is registered as thermal_zone4
[ 1.573673] ACPI: Thermal Zone [TZ4] (76 C)
[ 1.842871] tg3.c:v3.92.1 (June 9, 2008)
[ 1.843014] ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.843248] PCI: Setting latency timer of device 0000:08:00.0 to 64
[ 1.851292] usbcore: registered new interface driver usbfs
[ 1.851292] usbcore: registered new interface driver hub
[ 1.851292] usbcore: registered new device driver usb
[ 1.887291] eth0: Tigon3 [partno(BCM95751M) rev 4201 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:17:08:38:d1:b5
[ 1.887291] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 1.887291] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.887291] USB Universal Host Controller Interface driver v3.0
[ 1.887445] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 1.887679] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.887683] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.887939] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 1.888097] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00005000
[ 1.888296] usb usb1: configuration #1 chosen from 1 choice
[ 1.888439] hub 1-0:1.0: USB hub found
[ 1.888559] hub 1-0:1.0: 2 ports detected
[ 1.950780] No dock devices found.
[ 1.957132] SCSI subsystem initialized
[ 1.970780] Uniform Multi-Platform E-IDE driver
[ 1.970780] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.986780] libata version 3.00 loaded.
[ 1.994716] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.994838] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.996236] usb usb1: Product: UHCI Host Controller
[ 1.996351] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 1.996466] usb usb1: SerialNumber: 0000:00:1d.0
[ 1.997897] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 1.998133] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.998138] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.998278] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 1.998436] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00005020
[ 1.998634] usb usb2: configuration #1 chosen from 1 choice
[ 1.998777] hub 2-0:1.0: USB hub found
[ 1.998838] hub 2-0:1.0: 2 ports detected
[ 2.099828] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.099951] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.103710] usb usb2: Product: UHCI Host Controller
[ 2.103710] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.103710] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.103710] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.103723] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.103728] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.103868] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.104030] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005040
[ 2.104225] usb usb3: configuration #1 chosen from 1 choice
[ 2.104367] hub 3-0:1.0: USB hub found
[ 2.104484] hub 3-0:1.0: 2 ports detected
[ 2.204778] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.204897] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.205021] usb usb3: Product: UHCI Host Controller
[ 2.205136] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.205252] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.207710] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 2.207710] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 2.207710] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.207735] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.207890] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00005060
[ 2.208076] usb usb4: configuration #1 chosen from 1 choice
[ 2.208217] hub 4-0:1.0: USB hub found
[ 2.208334] hub 4-0:1.0: 2 ports detected
[ 2.307791] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.307909] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.308034] usb usb4: Product: UHCI Host Controller
[ 2.308148] usb usb4: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 2.308263] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.312488] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.312488] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.312488] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.312488] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.320483] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.320483] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.320483] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf4704000
[ 2.348126] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 2.360500] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.364482] usb usb5: configuration #1 chosen from 1 choice
[ 2.364482] hub 5-0:1.0: USB hub found
[ 2.364482] hub 5-0:1.0: 8 ports detected
[ 2.416574] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 2.461454] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.461573] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.461697] usb usb5: Product: EHCI Host Controller
[ 2.461812] usb usb5: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 2.461927] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.462095] ICH7: IDE controller (0x8086:0x27df rev 0x01) at PCI slot 0000:00:1f.1
[ 2.462228] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.462461] ICH7: not 100% native mode: will probe irqs later
[ 2.462584] ICH7: IDE port disabled
[ 2.462700] ide0: BM-DMA at 0x5080-0x5087
[ 2.462818] Probing IDE interface ide0...
[ 3.245777] usb 5-5: new high speed USB device using ehci_hcd and address 3
[ 3.354190] hda: UJDA770 DVD/CDRW, ATAPI CD/DVD-ROM drive
[ 3.440395] usb 5-5: configuration #1 chosen from 1 choice
[ 3.440720] usb 5-5: New USB device found, idVendor=13fe, idProduct=1d00
[ 3.440838] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3[ 3.440955] usb 5-5: Product: DataTraveler 2.0
[ 3.441070] usb 5-5: Manufacturer: Kingston
[ 3.441183] usb 5-5: SerialNumber: 5B78019D0083
[ 3.677782] usb 5-8: new high speed USB device using ehci_hcd and address 4
[ 3.689807] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 3.690031] hda: MWDMA2 mode selected
[ 3.690297] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 3.691745] ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 3.946793] ahci 0000:00:1f.2: version 3.0
[ 3.946813] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 3.980248] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[f4201000-f42017ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 4.022774] Initializing USB Mass Storage driver...
[ 4.055155] usb 5-8: configuration #1 chosen from 1 choice
[ 4.055402] hub 5-8:1.0: USB hub found
[ 4.055596] hub 5-8:1.0: 4 ports detected
[ 4.162640] usb 5-8: New USB device found, idVendor=04b4, idProduct=6560
[ 4.162640] usb 5-8: New USB device strings: Mfr=0, Product=0, SerialNumber=0[ 4.162640] scsi0 : SCSI emulation for USB Mass Storage devices
[ 4.162640] usbcore: registered new interface driver usb-storage
[ 4.162640] USB Mass Storage support registered.
[ 4.162640] usb-storage: device found at 3
[ 4.162640] usb-storage: waiting for device to settle before scanning
[ 4.436484] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 4.580478] usb 2-1: configuration #1 chosen from 1 choice
[ 4.652528] usb 2-1: New USB device found, idVendor=08ff, idProduct=2580
[ 4.652646] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0[ 4.652765] usb 2-1: Product: Fingerprint Sensor
[ 4.851926] usb 5-8.2: new high speed USB device using ehci_hcd and address 5[ 4.945981] usb 5-8.2: configuration #1 chosen from 1 choice
[ 4.945981] scsi1 : SCSI emulation for USB Mass Storage devices
[ 4.945981] usb-storage: device found at 5
[ 4.945981] usb-storage: waiting for device to settle before scanning
[ 4.945981] usb 5-8.2: New USB device found, idVendor=0ecd, idProduct=a100
[ 4.945981] usb 5-8.2: New USB device strings: Mfr=96, Product=76, SerialNumber=63
[ 4.945981] usb 5-8.2: Product: Mass Storage Device
[ 4.945981] usb 5-8.2: Manufacturer: USB2.0 External
[ 4.945981] usb 5-8.2: SerialNumber: DEF10D62F754
[ 5.175950] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
[ 5.176082] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 5.176210] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 5.179925] scsi2 : ahci
[ 5.179925] scsi3 : ahci
[ 5.179925] scsi4 : ahci
[ 5.180944] scsi5 : ahci
[ 5.180944] ata1: SATA max UDMA/133 abar m1024@0xf4705000 port 0xf4705100 irq 219
[ 5.180944] ata2: DUMMY
[ 5.180944] ata3: DUMMY
[ 5.180944] ata4: DUMMY
[ 5.296574] usb 5-8.3: new low speed USB device using ehci_hcd and address 6
[ 5.394366] usb 5-8.3: configuration #1 chosen from 1 choice
[ 5.396944] usb 5-8.3: New USB device found, idVendor=03f0, idProduct=0024
[ 5.396944] usb 5-8.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.396944] usb 5-8.3: Product: HP Basic USB Keyboard
[ 5.396944] usb 5-8.3: Manufacturer: CHICONY
[ 5.656036] usb 5-8.4: new low speed USB device using ehci_hcd and address 7
[ 5.798905] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.798905] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 5.799025] ata1.00: ATA-7: FUJITSU MHV2080BH PL, 892C, max UDMA/100
[ 5.799142] ata1.00: 156301488 sectors, multi 16: LBA48
[ 5.799552] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 5.799552] ata1.00: configured for UDMA/100
[ 5.814888] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
[ 5.824152] usb 5-8.4: configuration #1 chosen from 1 choice
[ 5.824824] usb 5-8.4: New USB device found, idVendor=046d, idProduct=c03d
[ 5.824943] usb 5-8.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.825068] usb 5-8.4: Product: USB-PS/2 Optical Mouse
[ 5.825181] usb 5-8.4: Manufacturer: Logitech
[ 5.825477] usbcore: registered new interface driver hiddev
[ 5.829708] input: CHICONY HP Basic USB Keyboard as /class/input/input1
[ 5.829987] hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
[ 5.830611] Uniform CD-ROM driver Revision: 3.20
[ 5.834787] Driver 'sd' needs updating - please use bus_type methods
[ 5.834989] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 5.835144] sd 2:0:0:0: [sda] Write Protect is off
[ 5.835271] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.835298] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.835488] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 5.835633] sd 2:0:0:0: [sda] Write Protect is off
[ 5.835758] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.835784] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.835887] sda:<6>input,hidraw0: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1d.7-8.3
[ 5.855849] input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
[ 5.860074] input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.7-8.4
[ 5.860623] usbcore: registered new interface driver usbhid
[ 5.860739] usbhid: v2.6:USB HID core driver
[ 5.921654] sda1 sda2 < sda5 sda6 > sda3
[ 5.967771] sd 2:0:0:0: [sda] Attached SCSI disk
[ 6.442709] PM: Starting manual resume from disk
[ 6.487118] kjournald starting. Commit interval 5 seconds
[ 6.487118] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.071592] Linux agpgart interface v0.103
[ 9.165167] input: Power Button (FF) as /class/input/input3
[ 9.213765] ACPI: Power Button (FF) [PWRF]
[ 9.214017] input: Sleep Button (CM) as /class/input/input4
[ 9.273279] ACPI: Sleep Button (CM) [C23B]
[ 9.277119] input: Lid Switch as /class/input/input5
[ 9.307237] ACPI: Lid Switch [C233]
[ 9.358032] ACPI: Battery Slot [C1B6] (battery present)
[ 9.358032] ACPI: AC Adapter [C1B4] (on-line)
[ 9.358032] ACPI: Battery Slot [C1B5] (battery absent)
[ 9.366035] ACPI: device:04 is registered as cooling_device9
[ 9.370033] input: Video Bus as /class/input/input6
[ 9.370033] ACPI: WMI: Mapper loaded
[ 9.419402] ACPI: Video Device [C12E] (multi-head: yes rom: no post: no)
[ 9.764296] usb-storage: device scan complete
[ 9.764915] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 9.766262] sd 0:0:0:0: [sdb] 3903488 512-byte hardware sectors (1999 MB)
[ 9.767012] sd 0:0:0:0: [sdb] Write Protect is off
[ 9.767145] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 9.767265] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 9.774975] sd 0:0:0:0: [sdb] 3903488 512-byte hardware sectors (1999 MB)
[ 9.775032] sd 0:0:0:0: [sdb] Write Protect is off
[ 9.775032] sd 0:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 9.775032] sd 0:0:0:0: [sdb] Assuming drive cache: write through
[ 9.775032] sdb: sdb1
[ 9.775488] sd 0:0:0:0: [sdb] Attached SCSI removable disk
[ 9.856639] Yenta: CardBus bridge found at 0000:02:06.0 [103c:30a3]
[ 9.856783] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[ 9.856898] IO window: 0x00006000-0x000060ff
[ 9.857016] IO window: 0x00006400-0x000064ff
[ 9.857076] PREFETCH window: 0x54000000-0x543fffff
[ 9.857076] MEM window: 0x50000000-0x53ffffff
[ 9.857076] Yenta: Enabling burst memory read transactions
[ 9.857076] Yenta: Using INTVAL to route CSC interrupts to PCI
[ 9.857076] Yenta: Routing CardBus interrupts to PCI
[ 9.857076] Yenta TI: socket 0000:02:06.0, mfunc 0x01011b22, devctl 0x64
[ 9.893079] input: PC Speaker as /class/input/input7
[ 9.931828] intel_rng: FWH not detected
[ 9.935470] tpm_inf_pnp 00:04: Found C1FA with ID IFX0102
[ 9.935639] tpm_inf_pnp 00:04: TPM found: config base 0x560, data base 0x570, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
[ 9.973569] sdhci: Secure Digital Host Controller Interface driver
[ 9.973692] sdhci: Copyright(c) Pierre Ossman
[ 10.048274] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 10.092274] Yenta: ISA IRQ mask 0x0cf8, PCI irq 18
[ 10.092274] Socket status: 30000006
[ 10.092274] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 10.092274] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 10.092274] cs: IO port probe 0x6000-0x6fff: clean.
[ 10.092274] pcmcia: parent PCI bridge Memory window: 0xf4200000 - 0xf45fffff
[ 10.092274] ACPI: PCI Interrupt 0000:02:06.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 10.092274] sdhci: SDHCI controller found at 0000:02:06.3 [104c:803c] (rev 0)[ 10.092274] ACPI: PCI Interrupt 0000:02:06.3[C] -> GSI 22 (level, low) -> IRQ 22
[ 10.092368] mmc0: SDHCI at 0xf4209000 irq 22 PIO
[ 10.116273] tifm_core: MMC/SD card detected in socket 0:1
[ 10.137848] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 10.137848] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[ 10.137848] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 10.137848] PCI: Setting latency timer of device 0000:10:00.0 to 64
[ 10.137848] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[ 10.198195] iwl3945: Tunable channels: 11 802.11bg, 13 802.11a channels
[ 10.198619] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 10.294198] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa44793/0x300000
[ 10.294198] serio: Synaptics pass-through port at isa0060/serio4/input0
[ 10.318919] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 10.330942] input: SynPS/2 Synaptics TouchPad as /class/input/input8
[ 10.349202] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 10.349464] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 10.358924] parport_pc 00:03: reported by Plug and Play ACPI
[ 10.358924] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 10.363213] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[ 10.363213] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.386921] Error: Driver 'pcspkr' is already registered, aborting...
[ 10.481972] usb-storage: device scan complete
[ 10.485887] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1H LL07 PQ: 0 ANSI: 0
[ 10.589808] cs: IO port probe 0x100-0x3af: clean.
[ 10.593809] cs: IO port probe 0x3e0-0x4ff: clean.
[ 10.593809] cs: IO port probe 0x820-0x8ff: clean.
[ 10.593809] cs: IO port probe 0xc00-0xcf7: clean.
[ 10.594417] cs: IO port probe 0xa00-0xaff: clean.
[ 10.723142] Driver 'sr' needs updating - please use bus_type methods
[ 10.732542] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 10.732777] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 10.777237] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 10.777237] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 10.777237] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 11.635579] Adding 232900k swap on /dev/sda6. Priority:-1 extents:1 across:232900k
[ 11.794196] EXT3 FS on sda3, internal journal
[ 12.840109] loop: module loaded
[ 12.939599] device-mapper: uevent: version 1.0.3
[ 12.939599] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 13.621554] pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
[ 13.621554] pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
[ 13.621554] pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
[ 15.334713] input: PS/2 Generic Mouse as /class/input/input9
[ 55.809137] lp0: using parport0 (interrupt-driven).
[ 55.821137] ppdev: user-space parallel port driver
[ 62.767387] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 62.767761] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 62.770983] firmware: requesting iwlwifi-3945-1.ucode
[ 62.851509] iwl3945: iwlwifi-3945-1.ucode firmware file req failed: Reason -2[ 62.851636] iwl3945: Could not read microcode: -2
[ 62.853779] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 62.996868] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 66.431566] Bluetooth: Core ver 2.11
[ 66.431566] NET: Registered protocol family 31
[ 66.431566] Bluetooth: HCI device and connection manager initialized
[ 66.431566] Bluetooth: HCI socket layer initialized
[ 66.608525] Bluetooth: L2CAP ver 2.9
[ 66.608525] Bluetooth: L2CAP socket layer initialized
[ 66.775250] Bluetooth: RFCOMM socket layer initialized
[ 66.775250] Bluetooth: RFCOMM TTY layer initialized
[ 66.775250] Bluetooth: RFCOMM ver 1.8
[ 100.793090] ISO 9660 Extensions: Microsoft Joliet Level 1
[ 100.825867] ISOFS: changing to secondary root
[ 101.015071] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 131.984532] pccard: CardBus card inserted into slot 0
[ 132.083506] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 132.083506] ohci_hcd 0000:03:00.0: enabling device (0000 -> 0002)
[ 132.083506] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 132.083506] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 132.083506] ohci_hcd 0000:03:00.0: OHCI Host Controller
[ 132.083506] ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
[ 132.083506] ohci_hcd 0000:03:00.0: irq 18, io mem 0x54000000
[ 132.163505] usb usb6: configuration #1 chosen from 1 choice
[ 132.163505] hub 6-0:1.0: USB hub found
[ 132.163505] hub 6-0:1.0: 1 port detected
[ 132.263623] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 132.263628] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 132.263631] usb usb6: Product: OHCI Host Controller
[ 132.263633] usb usb6: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 132.263636] usb usb6: SerialNumber: 0000:03:00.0
[ 132.263672] ohci_hcd 0000:03:00.1: enabling device (0000 -> 0002)
[ 132.263681] ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 18 (level, low) -> IRQ 18
[ 132.263711] PCI: Setting latency timer of device 0000:03:00.1 to 64
[ 132.263715] ohci_hcd 0000:03:00.1: OHCI Host Controller
[ 132.263742] ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 7
[ 132.263759] ohci_hcd 0000:03:00.1: irq 18, io mem 0x54001000
[ 132.359818] usb usb7: configuration #1 chosen from 1 choice
[ 132.359853] hub 7-0:1.0: USB hub found
[ 132.359864] hub 7-0:1.0: 1 port detected
[ 132.463918] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 132.463924] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 132.463927] usb usb7: Product: OHCI Host Controller
[ 132.463929] usb usb7: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[ 132.463932] usb usb7: SerialNumber: 0000:03:00.1
[ 133.849090] usb 6-1: new full speed USB device using ohci_hcd and address 2
[ 134.094028] usb 6-1: configuration #1 chosen from 1 choice
[ 134.112107] usb 6-1: New USB device found, idVendor=0c88, idProduct=17da
[ 134.112114] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0[ 134.112117] usb 6-1: Product: Qualcomm CDMA Technologies MSM
[ 134.112119] usb 6-1: Manufacturer: Qualcomm, Incorporated
[ 134.218029] usbcore: registered new interface driver usbserial
[ 134.218029] usbserial: USB Serial support registered for generic
[ 134.218029] usbcore: registered new interface driver usbserial_generic
[ 134.218029] usbserial: USB Serial Driver core
[ 134.222033] usbserial: USB Serial support registered for airprime
[ 134.222033] airprime 6-1:1.0: airprime converter detected
[ 134.222033] usb 6-1: airprime converter now attached to ttyUSB0
[ 134.222033] usb 6-1: airprime converter now attached to ttyUSB1
[ 134.222033] usb 6-1: airprime converter now attached to ttyUSB2
[ 134.222033] airprime 6-1:1.1: airprime converter detected
[ 134.222033] usb 6-1: airprime converter now attached to ttyUSB3
[ 134.222076] usb 6-1: airprime converter now attached to ttyUSB4
[ 134.222113] usb 6-1: airprime converter now attached to ttyUSB5
[ 134.222125] usbcore: registered new interface driver airprime
bastidasn@PC1:~$

Ufff, que difícil de leer...mira:

Clic en la imagen para ver un video de como insertar código:

ejecuta de nuevo pppconfig y pon /dev/ttyUSB5 (que al final parece que es el que se le asigna) en el apartado de port, mira si funciona y sino, postea el error que te de,

saludos

Buenas tardes, anexo mensajes emitidos luego de configurar la conexion con pppconfig:

AL colocar /dev/ttyUSB5 me da el siguiente error:

PC1:/etc/ppp/peers# pon internet
PC1:/etc/ppp/peers# plog
Jun 3 16:17:32 localhost pppd[5253]: pppd 2.4.4 started by root, uid 0
Jun 3 16:17:32 localhost pppd[5253]: Failed to open /dev/ttyUSB5: Exec format error
Jun 3 16:17:32 localhost pppd[5253]: Exit.

ESTE ES EL CONTENIDO DEL ARCHIVO DE CONEXION LLAMADO "INTERNET"

# This optionfile was generated by pppconfig 2.3.15.
#
#
hide-password
noauth
connect "/usr/sbin/chat -v -f /etc/chatscripts/internet"
debug
/dev/ttyUSB5
115200
defaultroute
noipdefault
user "XXXXXXXXXXX@movistar.com.ve"
remotename internet
ipparam internet

usepeerdns

Si coloco /dev/ttyUSB0: me aparece este esquema:

PC1:/etc/ppp/peers# pon internet
PC1:/etc/ppp/peers# plog
Jun 3 16:21:04 localhost chat[5493]: ATZ^M^M
Jun 3 16:21:04 localhost chat[5493]: OK
Jun 3 16:21:04 localhost chat[5493]: -- got it
Jun 3 16:21:04 localhost chat[5493]: send (ATDT#777^M)
Jun 3 16:21:04 localhost chat[5493]: expect (CONNECT)
Jun 3 16:21:04 localhost chat[5493]: ^M
Jun 3 16:21:05 localhost chat[5493]: ATDT#777^M^M
Jun 3 16:21:05 localhost chat[5493]: CONNECT
Jun 3 16:21:05 localhost chat[5493]: -- got it
Jun 3 16:21:05 localhost chat[5493]: send (\d)
PC1:/etc/ppp/peers#

dice conectado aparaentemente pero no logro Navegar en Internet.

Buenas tardes y, estare atento a sus comentarios.

buenas noches, hoy hice unas pruebas con algunas investigaciones a traves de internet y ma aprece el siguiente mensaje:

PC1:/etc# pon internet
PC1:/etc# plog
Jun 4 17:27:25 localhost chat[5059]: expect (CONNECT)
Jun 4 17:27:25 localhost chat[5059]: ^M
Jun 4 17:27:26 localhost chat[5059]: ATDT#777^M^M
Jun 4 17:27:26 localhost chat[5059]: CONNECT
Jun 4 17:27:26 localhost chat[5059]: -- got it
Jun 4 17:27:26 localhost chat[5059]: send (\d)
Jun 4 17:27:27 localhost pppd[5056]: Serial connection established.
Jun 4 17:27:27 localhost pppd[5056]: using channel 7
Jun 4 17:27:27 localhost pppd[5056]: Using interface ppp0
Jun 4 17:27:27 localhost pppd[5056]: Connect: ppp0 <--> /dev/ttyUSB0
PC1:/etc# plog
Jun 4 17:27:29 localhost pppd[5056]: rcvd [IPCP ConfNak id=0x1 ]
Jun 4 17:27:29 localhost pppd[5056]: sent [IPCP ConfReq id=0x2 ]
Jun 4 17:27:30 localhost pppd[5056]: rcvd [LCP TermReq id=0x4]
Jun 4 17:27:30 localhost pppd[5056]: LCP terminated by peer
Jun 4 17:27:30 localhost pppd[5056]: sent [LCP TermAck id=0x4]
Jun 4 17:27:30 localhost pppd[5056]: rcvd [IPCP ConfAck id=0x2 ]
Jun 4 17:27:30 localhost pppd[5056]: Discarded non-LCP packet when LCP not openJun 4 17:27:33 localhost pppd[5056]: Connection terminated.
Jun 4 17:27:34 localhost pppd[5056]: Modem hangup
Jun 4 17:27:34 localhost pppd[5056]: Exit.
PC1:/etc#

Estare atento a sus comentarios.

saludos.

Vamos que ya casi lo tienes, has visto esta página:

http://foxcarlos.wordpress.com/2008/04/10/como-configurar-una-tarjeta-pc...

Buenos dias, revise el procedimiento indicado, tal cual lo he hecho y no me funciona, disculpen mi indiscrecion, sera problemas de Kernel?, o de la ejecucion de algun comando adicional, saludos y gracias por la informacion que puedan suministrarme.